Претрага

Упит dcterms_subject_txt:auxiliary machines

77 items

  • Analysis of the exhaust emissions inventory from auxiliary mining machines

    Stevan Đenadić, Aleksandar Mirković, Jovana Mitrović, Filip Miletić, Predrag Jovančić, Dragan Ignjatović (2023)
    Open-pit coal mines are equipped with a large number of mining machines and vehicles with diesel engines. Due to common daily operation of these machines and vehicles large amounts of exhaust gases which contain numerous pollutants are emitted into the atmosphere. The demand to reduce air pollution induced the activities in developed countries to map and calculate all gases emitted by industries to formulate and select adequate preventive activities. In collaboration with machine manufacturers, emission standards for off-road machines ...
    emissions, mining, auxiliary machines

  • The optimization of auxiliary machinery in open-cast lignite mines: a case study of bulldozers

    Dragan Ignjatović, Predrag Jovančić, Stevan Đenadić, Ivan Janković, Ivica Ristović (2019)
    One of the most important prerequisites for the successful operation of the open-cast lignite mine is to carry out all the auxiliary works timely with the necessary quality. The most important and most commonly used auxiliary machines are bulldozers. Engaging time of bulldozers use is in direct relation with the coefficients of the time and capacity utilization of the continuous system for the excavation of coal and tailings, which indicates their importance. More than 100 bulldozers have been hired ...
    open-cast coal mine, auxiliary works, bulldozers, optimization, availability
    ... Therefore, benefits emerging from this attitude on auxiliary machines selection, including savings and improvements, can be achieved by these activities: In-time replacement of auxiliary machines and vehicles; Usage of proven and quality machines with implemented unification as much as possible; I ...
    ... cycle of that machihe. Keywords: Open-cast coal mine, auxiliary works, bulldozers, optimization, availabilifty. 1. INTRODUCTION Dozers are most common auxiliary machines at open-cast coal mines, both by type and the scope of tasks these machines can be used for. In the open-cast lignite mines of Electric ...
    ... that open-cast mines are having sufficient number auxiliary machines (namely dozers) should be included into determination of their life cycle. These machines will complete all planned tasks and create optimal conditions for operation of main mining machines (bucket wheel excavators, belt conveyors and stackers) ...

  • Analiza primene višekriterijumskih metoda u optimizaciji izbora hidruličnih bagera na površinskim kopovima uglja

    Stevan Đenadić, Predrag Jovančić, Dragan Ignjatović, Filip Miletić, Ivan Janković (2019)
    Hidraulični bageri primenjuju se u različitim oblastima privrede a najzastupljeniji su u građevinarstvu i rudarstvu. Na površinskim kopovima sa kontinualnim sistemima, klasifikuju kao pomoćna mehanizacija a na površinskim kopovima sa diskontinualnim sistemima, kao osnovna mehanizacija. Kako je u oba slučaja njihova primena neizostavna, važno je izvršiti adekvatnu analizu postojećih podataka, u cilju optimizacije izbora tipa hidrauličnog bagera u odnosu na uslove rada datog površinskog kopa. U radu su opisane različite višekriterijumske metode koje su korišćene za analizu hidrauličnih bagera. ...
    višekriterijumske metode, površinski kop uglja, pomoćna mehanizacija, hidraulični bager
    ... information which can affect the future purchasing decisions of this machinery. Key words: multi-criteria methods, open-cast coal mine, auxiliary machines, hydraulic excavators. https://doi.org/10.1016/j.procs.2015.07.081 https://doi.org/10.1016/j.procs.2015.07.081 ...
    ... in different areas of industry, most often in construction and mining. On open-cast coal mines with continuous systems, they are classified as auxiliary machinery, while on open- cast coal mines with discontinuous systems they are basic machinery. As their application is necessary in both cases ...

  • Application of the Fuzzy theory in the evaluation of operating parameters of auxiliary mechanization on open-cast coal mine, case study: pipelayers

    Stevan Djenadić, Miloš Tanasijević, Filip Miletić, Predrag Jovančić (2022)
    Achieved operating parameters are the main indicator of the work quality and selection of mining machines. The effectiveness of a coal mine is correlated with the availability of basic and auxiliary machines. The main task of auxiliary machines in lignite mines is to achieve optimal working conditions. From an economic point of view, auxiliary machines generate up to 20% of the lignite mines' total costs. These are the primary reasons for analyzing their current work and making decisions in ...
    upotrebni kvalitet, fazi teorija, rudarske mašine

  • Application of the Fuzzy Model in the Evaluation and Selection of Hydraulic Excavators on Open-Pit Lignite Mine

    Stevan Đenadić, Miloš Tanasijević, Vladimir Milisavljević, Dragan Ignjatović, Predrag Jovančić (2021)
    The production of lignite in large open-pit mines is mainly performed with continuously operating equipment, where bucket-wheel excavators, bucket-chain excavators, belt conveyors, and spreaders are the basic machines. Smaller machines, usually of discontinuous operating nature, are commonly categorized as auxiliary machines. This paper presents the research related to the analysis of auxiliary machine parameters with the case study for a hydraulic excavator. The purpose of the analysis was to develop a model of rating quality of service of the ...
    Fuzzy theory, hydraulic excavator, selection, quality of service, asset management

  • Development of the Cost-Based Model for Monitoring the Lifetime of the Earth Moving Machines

    Ugljesa Bugarić, Milos Tanasijević, Stevan Djenadić, Dragan Ignjatović, Ivan Janković (2022)
    This paper presents the model for the identification of reference points on the lifetime curve of engineering systems. This curve commonly represents the increase and decline of failure in relation to time. A direct correlation between failure rate and costs is assumed in this paper, therefore, statistical and empirical analysis of costs provided reference points. This approach is used for positioning stages of the engineering system’s lifetime with a minimal number of failures and costs, regardless of whether these ...
    Electrical and Electronic Engineering,Industrial and Manufacturing Engineering, Control and Optimization, Mechanical Engineering, Computer Science (miscellaneous), Control and Systems Engineering

  • Self-Engineering: Possibilities for Maintenance Operations in the Mining Machines Industry

    Steven Manders, Milorad Pantelić, Vladimir Milisavljević, Alberto Martinetti (2021)
    Self-engineering is a relatively new branch of knowledge that aims to understand how systems could “autonomously” re-configure or repair themselves without the intervention of the operators. A direct field of application is within the maintenance spectrum. Having systems or machines capable of self-detecting or even self-repairing could represent a game-changer, in capital asset fields such as the mining industry in particular. This paper aims to investigate the possible benefits and challenges of self-engineering / self-maintenance concerning mining machines, specifically bucket-wheel ...
    self-engineering, self-maintenance, maintenance operations, mining industry, bucket-wheel excavator, gearbox revitalization

  • Development of the Availability Concept by Using Fuzzy Theory with AHP Correction, a Case Study: Bulldozers in the Open-Pit Lignite Mine

    Stevan Đenadić, Dragan Ignjatović, Miloš Tanasijević, Uglješa Bugarić, Ivan Janković, Tomislav Šubaranović (2019)
    Availability is one of the most used terms in maintainability engineering. This concept is used to denote: The quality of service of an engineering system, i.e., machines, weak points’ analysis, asset management, as well as making decisions in the process of life cycle management. Availability is an overall indicator and contains partial indicators that are oriented towards reliability, maintenance, and logistical support. Availability presents a variable value and changes in time and space. Usually, availability is shown as the ...
    raspoloživost, fazi teorija, AHP višekriterijumska analiza, eksperska ocena, buldozer
    ... same conditions. The machines that are analyzed operate as auxiliary mechanization in an open-pit mine in the Electric Power Industry of Serbia’s Kolubara Mining Basin. The analysis covered three machines of type B1, 15 machines of type B2 and 14 machines of type B3. Machines are up to seven years ...
    ... with continuous systems is to carry out all necessary auxiliary works on time (cleaning the strips in striping and disposing, moving the transporter, making roads, etc.) [29]. This, of course, implies that the open-pit mine has enough machines and that they are available for operation. The direct ...
    ... efficiency of the auxiliary machinery and the operation of the basic mechanization (bucket-wheel excavators, belt conveyors, and spreaders) has been demonstrated. In case of low availability, the open-pit mine must have a larger number of units or there will not be enough machines for operation. In ...

  • Risk management of machines in open pit mines

    Kirin Snežana, Pantelić Milorad, Miljanović Igor (2013)

  • Analysis of noise sources in power transformers and rotating electrical machines

    Snežana Aleksandrović, Aleksandar Cvjetić (2015)

  • A Fuzzy Expert Model for Availability Evaluation

    Dejan Ivezić, Miloš Tanasijević, Predrag Jovančić, Radiša Đurić (2019)
    Each technical system within itself carries the great potential danger of possible occurrence of failure and damages. Mining machines are characteristic by great investment values, costs of unplanned shutdowns, complex working conditions, and environment and workers hazards. Systematic monitoring of the mining machinery is of great importance for the management of the mining companies. Availability is the overall concept of quality of service. Includes information regard to operating state, an idle state, a standby state and shut down. The ...
    raspoloživost, ekspertski sistem, fazi teorija, buldozeri
    ... AVAILABILITY OF BULLDOZERS Availability of bulldozers operating on surface lignite mines of Electric Power Industry of Serbia, which operate as auxiliary machines, is analyzed. Three different bulldozers (Liebherr - Lib, Dressta – Drs, Caterpillar - Cat), at three different surface mines (Drmno – D, Tamnava ...
    ... most common rate is “good” with a tendency towards ''average”. Figure 4.d shows that machines with the highest availability operate on the Field D, while the lowest availability is recorded for the machines on the Tamnava field. F. Verifications of results For bulldozers that operate at ...
    ... three different open pit mines in Serbia was evaluated using the proposed expert model. Machines were compared individually (selected machine at selected open pit mine), but also integral comparisons between machines and open pit mines were made. Obtain results should be used for the improvement of ...

  • Multi-Criteria Approach for Selecting Optimal Dozer Type in Open-Cast Coal Mining

    Ivan Janković, Stevan Đenadić , Dragan Ignjatović , Predrag Jovančić , Tomislav Šubaranović, Ivica Ristović (2019)
    Analitički hijererhijski proces (AHP), dozeri, eksploatacija uglja, površinski kopovi
    ... direct correlation with the work of the auxiliary (discontinuous) machinery, whose role is to accomplish all of the auxiliary workings on time. In effect, in the process of production in an open-cast coal mine, there must always be several different auxiliary machines available. The absence or insufficient ...
    ... direct correlation with the work of the auxiliary (discontinuous) machinery, whose role is to accomplish all of the auxiliary workings on time. In effect, in the process of production in an open-cast coal mine, there must always be several different auxiliary machines available. The absence or insufficient ...
    ... which consists of highly productive machines (bucket-wheel excavators, bucket-chain excavators, spreaders, conveyor-belt transporters, etc.) that provide an uninterrupted exploitation of mineral ores, the usage of auxiliary machinery is also necessary. The auxiliary machinery provides the possibility ...

  • A fuzzy-based decision support model for effectiveness evaluation - a case study of examination of bulldozers

    Miloš Tanasijević, Predrag Jovančić, Dejan Ivezić, Uglješa Bugarić, Radiša Đurić (2019)
    Effectiveness evaluation is one of the basic components of engineering asset management and maintenance engineering in general. Effectiveness is an overall concept representing a measurement of quality of service level for the analyzed engineering system. This concept contains a series of partial indicators relating to time in operation and time for maintenance activities, as well as functional properties of the system. This article describes the analysis and structuring of partial indicators, as well as the development of a model ...
    Efikasnost, Fazi zaključivanje, Prikupljanje podataka, Buldozer

  • Effectiveness Analysis of Different Bucket-wheel Excavators

    Stevan Đenadić, Predrag Jovančić, Dragan Ignjatović, Miloš Tanasijević, Filip Miletić (2021)
    Coal production in open-pit lignite mines in the Republic of Serbia is performed with continuous work systems. In addition to coal production, the same systems are used for the exploitation of large quantities of overburden. According to the reliability concept, continuous systems are in linear connection. If the failure occurs in one part of the system, that will produce a downtime of the entire system. The initial and most important factor of continuous systems is the bucket-wheel excavator. It ...
    bucket-wheel excavator, open-pit coal mine, mining, multi-criteria decision methods

  • Ostvarivanje dobiti pri uvođenju sistema agregatnih zamena na osnovnoj rudarskoj mehanizaciji površinskih kopova EPS

    Predrag Jovančić, Ignjatović Dragan, Đenadić Stevan (2021)
    Jedan od osnovnih zadataka na površinskim kopovima uglja je ostvarivanje zadovoljavajućeg vremenskog i kapacitetnog iskorišćenja kontinualnih sistema. Da bi se to postiglo, neophodno je izvršiti izmene u postojećoj strategiji održavanja. Preduslov je uvođenje agregatne zamene vitalnih delova na rudarskim mašinama. Benefiti su višestruki. Očekivani rezultati ovakvog pristupa su: smanjenje zastoja i povećanje vremena rada; direktne materijalne uštede; bolja organizacija rada; racionalizaciju radioničkih i magacinskih kapaciteta; povećanje vrednosti mašina. Da bi se uvela agregatna zamena neophodne su investicije za nabavku ...
    agregatne zamene, održavanje, mehanizacija, Benefit Cost analiza

  • Belt Weigher Accuracy Limiting Factors

    Aleksandrović Snežana, Jović Mihajlo (2010)

  • Underground loading-haulage equipment selection with application of topsis method with different weighting methods of criteria

    Vladimir Krivošić, Luka Crnogorac, Rade Tokalić (2024)
    The choice of adequate mining machines is one of the most complex problems in the underground exploitation of mineral raw materials. The weight of such a decision is reflected in the high prices of these machines and the occurrence of even greater costs during their use if their choice was wrongly conceived. There are numerous examples from practice in which such decisions were made solely on the basis of comparing the prices of machines, without considering any of the ...
    utovarno-transportna mehanizacija, izbor, TOPSIS, entropija, standardna devijacija, težina kriterijuma

  • Integrating landslide magnitude in the susceptibility assessment of the City of Doboj, using machine learning and heuristic approach

    Cvjetko Sandić, Miloš Marjanović, Biljana Abolmasov, Radislav Tošić (2023)
    In this work, landslide assessment of the Doboj City area was modeled by combining machine learning and heuristic tools. The machine learning part was used to map the Morphometric factor. i.e. probability of landslides based on relation between the magnitude of events and morphometric parameters: elevation, distance to streams, slope, profile curvature, and aspect. The Random Forest and Support Vector Machines algorithms were implemented in the learning protocol, which included several strategies: balancing of the training/testing set size, algorithm ...
    podložnost na kliženje, magnituda klizišta, mašinsko učenje, heuristički pristup, Doboj

  • Determining the Availability of Continuous Systems at Open Pits Applying Fuzzy Logic

    Miljan Gomilanović, Miloš Tanasijević, Saša Stepanović (2022)
    This work presents a model for determining the availability of continuous systems at open pits by applying fuzzy logic and fuzzy inference systems. The applied model was formed by the synthesis of independent partial indicators of availability. The model is based on an expert system for assessing the availability of continuous mining systems. The availability of the system, as a complex state parameter, is decomposed into the partial indicators, reliability, and convenience of maintenance, and the fuzzy compositions, used ...
    системи, континуални систем експоатације, површински коп, рударство, расположивост, фази логика, max–min композиција, min–max композиција

  • Fuzzy Model for Risk Assessment of Machinery Failures

    Dejan V. Petrović, Miloš Tanasijević, Saša Stojadinović, Jelena Ivaz, Pavle Stojković (2020)
    The main goal of this research was the development of an algorithm for the implementation of negative risk parameters in a synthesis model for a risk level assessment for a specific machine used in the mining industry. Fuzzy sets and fuzzy logic theory, in combination with statistical methods, were applied to analyze the time picture state of the observed machine. Fuzzy logic is presented through fuzzy proposition and a fuzzy composition module. Using these tools, the symmetric position of the ...
    fazi teorija, rizik, otkaz rudarskih mašina
    ... between machines, the work environment, and the environment in general, as well as the impact of unwanted failures on the operation of machines and the entire technical system, impose the need for constant monitoring and risk management. The smooth efficient operation of mining machines without failures ...
    ... parts of engineering systems are everyday occurrences in the mining industry, and they often lead to negative consequences that can have an impact on machines, employees, or the working environment. Such incidents are called risky events. In general, it can be said that an event that can influence the ...
    ... consequences and negative effects that can manifest after a failure. The consequences of a failure can have a negative impact on the structure of machines, employees, and the environment. The negative impact of an individual component failure can be reflected in reduced operational capacity or total ...